3D printed enclosures and housings
Enclosures for circuit boards, sensors, Raspberry Pi and Arduino projects, control boxes and instruments. PETG is the usual choice indoors, ASA for anything outside or near heat. Design walls at 2 mm, leave 0.3 mm clearance around a board, and put the lid and base in one order so they print from the same batch of filament.
A real example: a PETG enclosure 220 by 161 by 75 mm at 50% infill is £56.82 delivered on Standard, £116.38 next day, including VAT. Ten of them on Standard are £453.88 with the quantity discount, which is £45.39 each.


3D printed brackets, mounts and clips
The most common next-day part. Camera and sensor mounts, shelf and cable brackets, monitor arms, router mounts, clips for panels and trims. PETG for general use, carbon fibre PETG when it must not flex, nylon carbon fibre when it carries real load. A PETG bracket 90 by 53 by 14 mm is £25.09 delivered next day, £19.18 on Standard.
Tell us the critical dimension in the order note. The part is oriented so that dimension prints truest, and holes are drilled or reamed to fit on request.
3D printing car parts, motorcycle parts and RC parts
Interior clips, trim pieces, switch surrounds, cup holders, dashboard brackets, mirror and sensor mounts, bike fairing tabs, battery holders, RC chassis parts and bumpers. ASA handles the heat and sunlight of a car interior; nylon and nylon carbon fibre handle load and vibration near the engine bay. Print a replacement for a part the manufacturer no longer makes, or a part that never existed for your build.
Interior and trim parts
ASA. UV stable, warm-cabin tolerant, matte finish close to factory plastics. Clips, bezels, surrounds, vent tabs.
Under-bonnet brackets and mounts
Nylon or nylon carbon fibre, to about 150 °C. Sensor mounts, cable brackets, airbox tabs. Not for safety-critical, braking, steering or structural parts.
Motorcycle, bicycle and RC
PETG and TPU for guards, fairing fixings, mudguard tabs, grips and bumpers. RC chassis braces and wheel parts in carbon fibre PETG.
Spare and replacement parts for obsolete products
Knobs, handles, gears, latches, feet, covers and levers for appliances, tools and machines whose makers have stopped supplying them. If you have a file, upload it. If you have only the broken part, measure it and use the "I don't have a file" tab in the quote tool: send a sketch and the dimensions, and a person says whether it can be modelled and what it will cost. Simple parts with clear dimensions usually can.
NextDay3D does not reverse engineer from photographs alone, because a photo has no dimensions. A sketch with measurements, or the broken part's key sizes, is enough for most clips and knobs.
What to send for a part with no file
- Overall length, width and height, measured with a ruler or calipers.
- Hole sizes and centre distances, if there are any.
- A photo of the part beside a ruler, and a photo of where it fits.
- What it does: does it clip, screw, slide, carry weight, or get hot?
- How many you need and when.
Jigs, fixtures, tooling and custom one-off parts
Drill guides, assembly jigs, soft jaws, inspection fixtures, cable combs, tool holders and organisers, printed overnight so the shop floor has them in the morning. Carbon fibre PETG is the workhorse: stiff, dimensionally stable, matte. Nylon carbon fibre where clamping loads are high. PETG for anything that just needs to hold position.
Custom one-offs of any kind follow the same route: upload, price, order by 12:00. There is no tooling, no setup charge on FDM, and no minimum beyond £9.99 of print price per material. Post-processing is included where it matters: supports removed and contact points cleaned on every part, holes reamed on request, and sanding as an option in the tool.

What a next-day part costs
Real single-part orders from 2026, delivered to a UK address, including VAT. The exact price for your own file appears in about 20 seconds.
| Part | Material | Standard | Express | Next Day |
|---|---|---|---|---|
| Clip, 107 by 50 by 14 mm | PLA | £19.18 | £21.44 | £23.71 |
| Bracket, 90 by 53 by 14 mm | PETG | £19.18 | £22.14 | £25.09 |
| Plate, 333 by 110 by 4 mm | PLA | £28.38 | £41.10 | £53.81 |
| Enclosure, 220 by 161 by 75 mm | PETG | £56.82 | £86.60 | £116.38 |
| Tall housing, 486 by 219 by 189 mm | PLA | £108.85 | £169.85 | £230.84 |
3D printed parts questions
Can I get a custom part 3D printed and delivered tomorrow in the UK?
Yes. Upload the file to NextDay3D before 12:00 on a working day, choose Next Day, and the part is printed the same afternoon and delivered the next working day by Royal Mail tracked post, from £19.97 including VAT and delivery.
Can you 3D print car parts?
Yes, for interior, trim and non-structural parts: clips, bezels, surrounds, brackets, mounts and holders. NextDay3D prints them in ASA for heat and UV or nylon for load. It does not print safety-critical, braking, steering or structural components.
Can you 3D print a replacement part from a photo?
Not from a photo alone, because a photo has no dimensions. Send a sketch with measurements, or the key sizes of the broken part, through the "I don't have a file" tab in the NextDay3D quote tool, and a person says whether it can be modelled and what it will cost.
Are 3D printed parts strong enough for real use?
For brackets, enclosures, clips, jigs and most replacement parts, yes. PETG is around 50 MPa tensile strength, carbon fibre PETG about 60 MPa and nylon carbon fibre about 100 MPa. NextDay3D prints at 0.2 mm layers with walls flagged below 1.5 mm, and orients parts so the load runs along the layers where it can.
How big a part can you 3D print?
Parts over 500 mm long and 480 mm tall have been printed in one piece on NextDay3D's own printers. Upload the file and the tool says whether it fits; larger parts are printed in sections and joined, and a person confirms the approach before you pay.
Do you keep my files for reorders?
Yes, on your account, with the settings used, so the same part can be ordered again in one click. Files are seen only by the people who print them and are deleted when you ask.
Can you print 3D printed parts in bulk?
Yes. Quantity discounts on the print price start at 10 units (10%) and reach 30% at 250. Ten PETG brackets are £51.58 delivered on Standard, £5.16 each including VAT.